Coupe for sale in Meridian, Idaho

Chevrolet : Corvette 1965 corvette coupe resto mod fresh restoration show winner

$70,000

Meridian, Idaho

1965 Corvette Coupe Complete Fresh Restoration as described below Ready to Enjoy-Drive or Show About 200 break-in miles since completion in Spring 2015It drives beautifully and looks even better. Three Shows/Three Awards including “First Place Sports Car” and “Outstanding Sports Car” Boise Roadster Show “Best Corvette” Valley Corvettes Corvette-Only Spring Show When I bought this car about 2 1/2 years ago is was a good running and nice appearing car with 70,000 original miles but I wanted to completely restore it. When I purchased it, the car was fairly original but (as you will read below) the original engine and transmission were long gone. The previous owner gave me the ownership history back to the original owner who lived in Florida. I have all the names of those owners, addresses and telephone numbers most of which have surely changed over the past 50 years. The last three owners let it sit for ten years each so most of the 70,000 miles per put on the car during the first twenty years of its life.Then the car was 6 months old it was stolen from the owner in Florida and recovered in Georgia. In the state of Georgia they still have a law that says if a stolen car is recovered in Georgia it gets a new VIN. That's what happened to this and many other Corvettes of this era. I am sure this point will be of concern to a buyer just as it was to me. Since the reVIN, the car has been bought and sold several times without a problem. When I bought the car out of state and had it retitled in Idaho I had to have it inspected just because it came from out of state. There was no problem getting it retitled in Idaho since the paperwork is all in order.I also have a document from the time the VIN was changed that shows the original VIN plus the new VIN. Possibly is some states the original VIN can be reinstated but not in Idaho. It only really matters if you wanted to have this car judged as original and since it is a resto-mod it probably doesn't matter.I wanted to make this car look very special and stand out from all the other C2 Corvettes. 1965 was the last year of old-school Rochester mechanical fuel injection. I like the look of the Rochester FI but not the dependability. I started out with a GM Performance Ram Jet intake manifold and electronic ECU controlled fuel injection system. I sent the intake manifold to Arizona Speed and Marine in Phoenix. They modified it to look like a Rochester dog-house FI set-up. The throttle body was moved from the front to the drivers side as you can see in the photos. I built a custom intake system to look similar to (but flashier than) the original. Finally the ECU was reprogrammed for optimum performance with the ZZ4 Fast Burn motor. I am very happy with the results. It is really fun to see the puzzled look on Corvette enthusiasts faces as they look at the motor and try to figure out what they are looking at.As you will read below, I have made many updates to the car to make it more modern and fun to enjoy without changing the best parts of the original design. When Peter Brock signed the dash he was very complimentary on the car and how it turned out.Finally, I am a detail oriented person so I have included a complete build list of all the parts I have put on this car. I know it is difficult to evaluate a car on eBay from photos and a written description. I have put all the photos that eBay will allow but if you are really interested in this car I can send you a link where you can see about 140 detailed photos top to bottom. History Original Factory Issued VIN 194375SXXXXXX Assembled St Louis Plant April 13, 1965 Original equipment as delivered new: 350hp, 327ci solid lifter motor Muncie M-20 4-speed transmission AM/FM radio 3.55 Posi-traction differential Rally Red exterior paint Red vinyl interior Delivered to first owner in Florida Stolen about six months later Recovered in Georgia new VIN issued Clean Idaho title that I guarantee you can retitle anywhere Documentation of original VIN, reissued Georgia VIN and current Idaho VIN and title included with sale documents All ownership history names and addresses provided with sale documents Approximately 70,xxxx original miles Restoration and Rebuild of Major Parts Bodywork and PPG respray Rally Red Blackout and underbody surfaces PPG Black Frame and all suspension parts sand blasted and painted with gloss black Imron epoxy 1968 Muncie M-20 transmission rebuilt Original 3.55 Posi-traction differential rebuilt Drive shaft and propeller shafts rebuilt with new U joints Rear transverse spring rebuilt Original bumpers rechromed by Librandi of Pennsylvania Original AM/FM radio serviced Windshield wiper motor serviced Restoration Upgrades GM Performance ZZ4 fast burn 385 hp motor Custom Ram Jet Fuel Injection Intake by Arizona Speed and Marine Delphi MEFI 4 fuel injection management system Custom air intake system March Style-Track Billet Aluminum Serpentine Pulley System March Billet Remote PS Reservoir Boyd's 17" Junkyard Dog Aluminum Wheels Toyo Proxes 4+ Front 225/45R-17 Rear 245/45R-17 Tires QA-1 Sharkbite Coil Over adjustable shocks 450# Medium Billet Specialties steering wheel All suspension rebuilt with new ball joints, urethane sway bar bushings, tie rods, rear shocks New calipers, rotors, wheel bearings, seals Headman ceramic coated headers 2 1/2" Exhaust with Magnaflow mufflers and DEI Titanium exhaust wrap Lakewood bell housing Centerline dual force clutch Dewitt aluminum radiator with electric fan Vintage Air Conditioning Borgeson Retro steering box 12.5:1 quick ratio Rock Valley Stainless Steel Fuel Injection fuel tank with pump and sending unit Detroit Speed Headlight motor management conversion kit Hurst shifter Joe's billet short shifter lever Joe's billet shift knob C5 Corvette red leather sport seats Custom console box covered with French double stitched matching red leather Console covered with French double stitched matching red leather Dakota digital electric fan controller and relay Optima red top battery Dynamat floor covering Wilwood brake master cylinder 7/8 polished Stainless steel brake lines Stainless steel brake hosesPerformance Products "Corvette" script aluminum valve covers with fasteners Tachometer conversion from mechanical to electric Amp meter conversion to volt meter Clock conversion from analog to digital Al Knoch Carpet set MP3 radio adapter Three point seat belt conversion New Parts Radio knobs Radio antenna mast and motor Windshield wiper blades Lighter with element Vent crank seals Window crank handles Window crank protector Vent crank protector Door weather stripping Door glass weather seals Floor mats Kick plates and screws Grille and mounting hardware Motor and transmission mounts Glove box light and switch Glove box door stop Glove box grommets Glove box screw set Glove box U-nut set Console repair kit Brake pedal pad Clutch pedal pad Door blackout Glove box light shield Glove box liner screws Glove box lower hinge screws Front parking brake cables, clevises bushings complete kit Seat side rails Fuel Injection emblems High torque starter Top ignition shield cover Top ignition shield cover brackets, fasteners, chrome wing bolts and looms Firewall wiring J clips Gas Pedal Rocker panels Rocker panel support U nuts Rocker panel support screws Steering column seal Nose headlight support rods Ground strap kit Battery hold down spacers Headlight housing spacers Headlight pivot ball felt seal Headlight pivot ball rubber seal Headlight ball seal washer Headlight pivot support bearing Headlight nose support rod bracket bolts headlight motor retainer clips door gasket set Gas guard Headlight Support Male Trinary AC switch Rag joint Headlight bucket hole plug Headlight extension wire connector Headlight limit switch screws Headlight outer pivot shaft Headlight inner pivot shaft Headlight bezel screws Headlight bezel J clips Headlight pivot screw kit Rocker molding screw set Painless wire wrap Radiator and heater hoses Gates Powergrip hose clamps Intake manifold gasket Fuel pump cover plate and gasket Pinch welt and screws Window inner corner trim molding Oil pressure gauge line kit Inside rear view mirror Inside mirror support Inside fasteners Headlight motor bracket screws Headlight motor bracket grommet screws Turn signal handle WIX 33481 Fuel Filter Fuel filter bracket Head gaskets and head bolts Odometer decal Steering column support at firewall Screws for above Valve Cover Gaskets Drive belt Drive belt Valve cover gaskets Dash upper insulation Firewall insulation Gas tank strap ant squeak AC Fittings 5/8 90 degree chrome heater hose fitting Lokar Dipstick Expansion tank 90 degree top heater water outlet speedo grommet Battery cables Battery Cable clamps Clock clips Gas pedal spacer Gas fill neck cork gasket Headlight main wiring harness headlight extension wiring harness Engine wiring harness Tail light wiring harness Wiring harness clips Spark plug wires NKG spark plugs, rotor and cap Spark plug wiring grommet Interior light bulb set Power vent screen Washer hose clips Washer hoses Rear vent cardboard vent cover screws 150 amp circuit breaker Brake line fittings Parking light housings, lenses and pigtails Tail light housings, lenses and pigtails Park light screws Dash rivets Clutch pivot stud lock Clutch cross shaft felt seals Clutch shaft plug Clutch fork anti rattle spring Clutch return spring bracket Clutch return spring bracket Clutch pedal bracket G retaining clips Brake pedal return spring brake pedal spring bushing brake pedal clevis washer Clutch and brake pedal bushing set brake bumper Clutch pedal push rod bracket bolts Spark plug wire supports and looms Hood latch release cable Fuse blocks Clutch pedal bumper Gauge gaskets Steering column clamp Flasher clip Odometer knob Packard connectors, Weatherpack connectors Fuses Rear Upper Interior red Vinyl Air box and filter Air intake elbow, flexible boot and clamp Air intake flexible boot, clamps and spacer Air intake sleeve kit Air Intake clamp Air intake aluminum tube T Bolt Clamps Duct mount flange Air intake flex hose Replacement horns Radiator support trim Rear license plate light lens Rear license plate light assembly screw set Rear license plate light lens screw set Fuel line clips Wire Wrap Fuel pressure relief valve seal Alternator cable Misc fasteners Electrical wire Wiring terminals stainless steel wrapped fuel Lines Fuel line fittings Washer fluid Power steering fluid C3 seat tracks Fuel Log Schrader valve and cap Fuel Line and fittings Fuel line fittings AC fittings Power steering fittings Power steering hoses braided stainless steel Antifreeze Fuel tank drain hose Accelerator rod pivot bushing Water temp sending unit Seat track springs Outside Script mirror Seat track knobs Turn signal lever Fabrication metal and pop rivets Spray adhesive Lower steering column bearing Front wheel bearing grease caps Brake cable brackets Powder coat steering column Spray adhesive Fuel Pressure Gauge Fuel Pressure Gauge fitting Seat belt guides Throttle body gasket Brake fluid Caliper spray paint Brake pad anti squeak Mobile One 5-30w synthetic oil and filter Jack board bezel Long spring bolts and bushings Cups for above Parking brake cable clips (pair) Brake fluid Brake line spacers DEI Titanium exhaust wrap Gear lube Shims Wheel bearing grease and packer Cup holder Chrome Halogen fire extinguisher Front and rear end alignment Idler arm grommet Front small door access plate door lock bezel gasket door lock knob spacer 3M Defender spray on rear lower quarter panels behind rear wheels Charge AC Turn Signal Switch Dash bezels 32 oz 90 wt gear oil for transmission

Nissan : GT-R Nissan GTR 1989 nissan skyline gt r gtr 100 fed legal already in usa rb 26 dett awd rhd

$15,999

Meridian, Idaho

THIS IS A NO RESERVE AUCTION. This is a 1989 Nissan Skyline GTR AWD Twin Turbo with the RB26DETT motor and 5speed manual trans. BNR32-001004 It is listed as a 1980 due to ebays rules on vehicles newer than this requiring a 17 digit vin, JDM cars to NOT have a 17 digit vit. This cars vin is BNR32-001004 This car is FEDERALLY legally, and imported with ALL of the correct/legal paperwork such as the Bond Release. All import taxes/tariffs have been paid upon importing. Its 100% ready for the new owner. I have sold a few 1989 GTRs and they are all registered with the new owners and have had no problems. You will be the first registered owner in the USA. You can register just like any other vehicle in ANY state except Cali and Hawaii. (Due to local laws in those states) If you have any questions about this don’t hesitate to contact me. CAR IS LOCATED IN THE USA ALREADY. Located in Boise, Idaho. Can be seen in person. Only serious buyers with funds in place ready to go please. I can help arrange shipping as well, but shipping expense is up to the buyer. $500 non refundable deposit is due at the auctions end. The car has 132,xxx KM on it, so about 82k miles. The car has had a FRESH pain job. The body is in great shape with not a single dent/ding/scratch. It was painted the OEM color. Its a True GTR (BNR32-001004)but previous owner had a GTS front bumper on it trying to go for the " sleeper " look. The front window trim is also not on the car, but I have a pair I will be including. It’s a nice stock base to build your dream beast with. It’s not a 100% perfect example but like i said the paint is in great shape, I have uploaded a video and provided a link at the bottom of this listing. Please be sure to check it out. It gives a great idea on the overall condition of the car. The main flaws on this car are its interior. It has a small aftermarket steering wheel that for me is too small, its also missing both door speakers, and grills that cover the speakers. The dash does NOT have cracks in it, and the door panels/seats are in good shape. It doesn't have floor mats and due to this the carpet is dirty/worn in the front. Mechanically the car starts up and runs/drives fine. I have a video at the bottom of the auction doing a few short pulls to show it pulls through the gears smoothly with no sputter/hesitation. Occasionally it grinds going into 3rd gear. Transmissions can be found on ebay for $500, I just don't have the time to replace it. The car also does not have Air Conditioning. The cars undercarriage is NOT all rusted out either. I took photos of under the car as many buyers want to see this so please be sure to look. If you have other questions just ask. I have described everything to the best of my knowledge. This is a NO reserve auction, and will be sold to the highest bidder. Please only serious bidders. $500 non refundable deposit due at auctions end. Car sold AS IS, with no warranty expressed or implied Modifications - Aftermarket Authentic Old school 2 piece VOLK wheels - Front Mount intercooler with hard pipes - Aftermarket intake kit - Boost gauge - HKS Turbo Timer - Aftermarket TOMEI 310KM/HR Cluster - Aftermarket steering wheel - Aftermarket Greddy/ Trust exhaust-HKS SSQV BOV - Aftermarket ECU with 8500 redline - Get your own valid XHTML YouTube embed code Get your own valid XHTML YouTube embed code Get your own valid XHTML YouTube embed code

Trim GTR

1970 Dodge Challenger Ta for: $85000

$85,000

Meridian, Idaho

1970 Dodge Challenger Ta This is a True Bad Ass1970 Dodge Challenger T/AThis Challenger is immaculate from top to bottom. Every Single Detail has been put into restoring this piece of Awesome Automotive History.The restoration was a complete frame up nut and bolt rotisserie restoration. We began the restoration in April of 2011 and it was completed January of 2012. Every single inch of this car has been gone through and restored back to its original factory representation with factory original parts with no exceptions. No expense was spared.The VIN tag Radiator Support Tag and Cowl Tag are all numbers matching.VIN DecodedJ - Car Line: Dodge ChallengerH - Price Class: High23 - Body Style: Hardtop CoupeJ - Engine: Engine : 8-cyl. 340cid/290hp 3x2bbl Six Pack0 - Year: 1970B - Assembly Plant: Hamtramck MI289853 - Production NumberThe Block is a 340 Six Pack factory replacement with production stamp with around 1000 miles on it. (Probably less as I have only driven it about 100 miles personally)Engine runs perfectly with zero issues.Nothing beats the sound and the feeling of an all American Muscle Car! All glass is factory original with Chrysler stars. Comes with 2 sets of tires. The first set are original Polyglass tires from a 1970 Dodge Challenger T/A that are in excellent condition the second set are BFGoodwrich which are also to spec for Sunday driving.Transmission is the original with brand new gears built to spec for T/A. (Rebuilt in April 2012) Shifts Perfectly!Rear End is a 355 Sure grip. (Completely Rebuilt to Factory Specs in late 2011)Fender Tag CodesE55 - 340 CI 3X2 V8 290 HPD21 - 4 Speed Manual TransmissionJH23 - Challenger T/A 2 Door Hard TopJ0B - 340 CI 3X2 Carb 8 Cylinder 1970 Dodge MainHamtramck MI USA289853 - Sequence NumberFC7 - Plum Crazy Exterior ColorH6X9 - High Bucket Seats000 - Full Trim Doors325 - Production Date193693 - Order NumberFC7 - Plum Crazy Top ColorA53 - Trans Am PackageB51 - Power Front Disc BrakesC55 - Bucket SeatsC34 - Left Outside MirrorJ45 - Hood Tie DownsJ54 - Sport HoodJ82 - Rear Deck SpoilerM21 - Drip MoldingsN44 - Side ExhaustN94 - Fiberglass Freshair HoodR11 - AM RadioV6H - Longitudinal Stripes Trans Am BlackY05 - USA Build Specs26 - 26 Inch RadiatorEN1 - End of Sales CodesThis truly is an amazing car. You will not find another 1970 Dodge Challenger T/A on the market with the same originality or attention to detail!Hagerty Valuation Chart:https://www.hagerty.com/valuationtools/HVT/VehicleSearch/Report?vbe=105174This is by far a Barrett Jackson or museum worthy car!Please direct any Business/Sales Questions to Brian at 208-695-4695Please direct any Technical/Build Questions to Dave at 530-370-4459SERIOUS INQUIRIES ONLY!Thank you very much for looking! We look forward to hearing from you!

Nissan : GT-R GTR Nissan Skyline GTR GT-R R32 AWD RB26DETT Federally legal in USA RHD modified

$20,000

Meridian, Idaho

This car is FEDERALLY legally, and imported with ALL of the correct/legal paperwork such as the Bond Release. All import taxes/tariffs have been paid upon importing. Its 100% ready for the new owner. I have sold a few 1989 GTRs and they are all registered with the new owners and have had no problems. You can register just like any other vehicle in ANY state except Cali and Hawaii. (Due to local laws) If you have any questions about this don’t hesitate to contact me. CAR IS LOCATED IN THE USA ALREADY. Located in Boise, Idaho. Can be seen in person. Only serious buyers with funds in place ready to go please. I can help arrange shipping as well, but shipping expense is up to the buyer. Car is in great condition and runs and drives nicely. It’s not a rusted out car. It’s really a nice stock base to build your dream beast with. It’s not a 100% perfect example, but it is in better shape than most cars its age (and even some of the other GTR’s I’ve sold) It’s had some simple maintenance done and is ready for the new owner. I will touch base on some of the flaws below. I have uploaded a video and provided a link at the bottom of this listing. Please be sure to check it out. It give a great idea on the overall condition of the car. The interior also is in good shape, the only flaws being the driver seat bolster and the driver door panel. You can see these areas highlighted in the photos. The dash is not cracked, NO Check engine lights either. If you have other questions just ask. I have described everything to the best of my knowledge. List of mods; R33 RB26 Engine swapped with about ~90,000km on it. ( 59,000 miles) Cusco front strut bar FMIC (factory) Blitz Dual Drive BOV x2 Aftermarket clutch Blitz Technospeed Z1 Wheels 17"BF Goodrich KDW 17" ( Lots of life left still) Trust 3" downpipe Trust 3" Titanium cat-back Sard 3" high flow Cat HKS Twin air filterAftermarket CD player Recent maintained done- Turbo gaskets have been replaced. Power steering boot and axle boots have also been replaced. Engine oil, diff oil, transmission oil, transfer case oil have all recently been replaced, as well as the HKS air filters. Get your own valid XHTML YouTube embed code

Trim GTR

Chrysler : Crossfire Limited Convertible 2-Door 2005 chrysler crossfire limited roadster convertible

$11,000

Meridian, Idaho

Have a nice red Crossfire for sale. Has 25230 miles, standard transmission, heated seats, power seats, cruise, a/c, power steering, convertible top. The top was just replaced last year from a Chrysler dealer so its pretty new. Has very good tires. Has been in garage under cover for about last 5 years. Still runs great. Top works

Trim Limited Convertible 2 Door

1973 mg mgb roadster

$6,200

Meridian, Idaho

I restored my 1973 MG model B Roadster. It was repainted to it's original color, white, by a professional and most of the pieces and parts have been replaced with brand new ones, -brand new soft top -brand new interior kit -brand new tires with less than one mile on them! are to name just a few! The pictures speak for themselves. It runs great and sounds great! NO rust! I have the title in hand and it is CLEAN! Feel free to contact me for more information : [email protected]