Hatchback for sale in Millbury, Massachusetts
1-2 of 2
Sort By
Ford : Focus SVT Hatchback 3-Door 2003 ford focus zx 3 svt only 20 409 original miles
$8,995
Millbury, Massachusetts
2003 FORD FOCUS ZX3 SVT ONLY 20,409 ORIGINAL MILES - 6 Speed Manual - Winter Package - Heated Front Seats - Traction Control - Block Heater - Keyless Entry - Power Windows - Power Sunroof - Power Mirrors - Power Locks - Steering Wheel Controls - Cruise Control - 17" Alloy Wheels - Side Airbags - Fog Lights - Am/FM Radio - 6 Disk Cd Player - All Original Floor Mats - Heat and Cold AC! - All The Books and Owners Manuals - 100% FACTORY ORIGIONAL WITH NO MODIFICATIONS - EXTREMELY HARD TO FIND A CAR LIKE THIS WITH THESE MILES BRAND NEW BRAKES ALL AROUND (Pads and Rotors) 4 GREAT HANKOOK V12 EVO TIRESI would NOT HEAISATE to drive this car cross country just the way she sits!Please contact me with any questions or for specific additional pictures. ----- $8,995 -----OR BEST OFFERI can pick up any serious buyer at (PVD) or (BOS) Airport to make the deal happen. they are both located less than 45 minutes away from me.
Trim SVT Hatchback 3 Door
Nissan : 200SX SE-R Coupe 2-Door 1997 nissan 200 sx se r coupe 2 door 2.0 l built sr 20 de
$5,000
Millbury, Massachusetts
I am selling my 97 Nissan 200sx SE-R. This a very fun and capable car I have roughly 15,000.00 in performance modifications done. The engine was built with the intent on turboing the car but never got around to installing the turbo. The car runs and drives dependably but I'm affaid I have to sell, I enlisted in the U.S. Army and couldnt take the car with me. The cylinder head was disassembled, cleaned, inspected, and reassembled with the following components: -competition 3 angle valve job with 0.040" valve seats -Valve job performed on a Serdi machine -cylinder head ported and flow tested on a SuperFlow 600 flow bench using Audie Technology digital interface -exhaust valve guides replaced with manganese bronze and honed to spec -all 16 valves reground using Kwikway valve grinding machine -cylinder head deck milled to ensure flatness(0.010" deckmill) -valve shims ground to fit Tomei solid lifters -fwd sr20de valve cover powder-coated black with breather baffles removed and rear breather tube plugged off -HKS adjustable camshaft gears -Greddy rocker arm stoppers -Tomei solid lifter -Peak Performance race spec valve springs -oem valve stem seals -HKS 272 step 3 intake camshaft(228 degrees at 0.050" lift, 12.6mm lift) -Nismo 280 exhaust camshaft(224 degrees at 0.050" lift, 12.6mm lift), this is an extremely rare camshaft. it was briefly made and I had to buy it directly from a distributor in Japan. -FWD Cometic 0.040" MLS head gasket -Nissan Pulsar GTI-R individual throttle bodies -Cutsom made intake plenum -Profab insulating intake manifold spacer gasket - Nissan Pulsar GTI-R 444cc injectors -IAT Sensor -Wired up for map sensor (planned to boost it the spring) -AEM Series 2 stand alone ecu -Greddy Front&Rear sway bars -Tokiko Blue struts -TIEN lowering springs -Full custom 3'' exhaust (done by Lou's Custom Exhaust) -Custom intake manifold (done by T&M Performance) -Custom cold air intake (done by Lou's Custom Exhaust) There are a lot more modifications but this list is just off the top of my head I also have a rwd race plenum for the individual throttle boddies. I had a 240sx that this build was going to go into but I went a different route. Now the cons: -Rust on the rear quarter needs some attention -I put a new factory front end on the car which is primed black the car needs to be painted. -Needs a battery I'm asking 5000.00 no low ball offers there is a lot of time and money into this car serious inquiries only
Trim SE R Coupe 2 Door
