Chevrolet C 10 none cars for sale

1-15 of 15

Sort By

Chevrolet : C-10 none 67 72 pro touring rolling chassis ridetech coilovers no limit 4 link

$10,500

Coatesville, Indiana

Year 1968

Make Chevrolet

Model C-10

Category -

Mileage 9999999

Posted Over 1 Month

This is a boxed and heavily braced 1967-72 shortbed c10 frame that uses all factory body mounts, steering component mounts, motor mount holes, and requires no modifications to the bed floor or inner fenders. The frame rails were boxed with 11 gauge steel and were gapped,beveled, welded and ground smooth. The bracing is all 11 gauge as well and has an adjustable trans mount that sits at the same height as factory.The frame is obviously much more rigid than a stock frame but the bare frame and crossmembers only weighs about 75 lbs more than the stock frame and crossmembers and by the time you compare coilovers to stock springs/shocks and the weight difference between stock trailing arms and the 4 link tubular arms the weight difference is about 50 lbs. The setup is designed to be either a 3/5 drop or a 4/6 drop but everything is adjustable front and rear. The rear has been recentered in the wheel opening as opposed to some lowered trucks where the wheel sits close to the front of the wheel opening. There are 3 1/2 in diameter exhaust cutouts in the frame to allow a tucked clean looking exhaust system. The front crossmember was acid dipped to get all the rust even on the inside and the frame was sandblasted before and lightly again after all the fab work was done. ALL body mounts and crossmember seams were seamsealed, everything was bodyworked,sprayed with epoxy, then hi-build primer, sanded down once and sprayed again with hi-build. The front end includes RIDETECH strong arms upper and lower A arms for added strength,geometry, and caster adjustabilty for aggressive driving, 2 1/2 in drop spindles, RIDETECH musclebar sway bar with posi-links and all 4 wheels are height and rebound adjustable with RIDETECH handling series coilovers. The rear is a ford 9 inch that is narrowed to the same width as stock and has a rebuilt posi unit(at MOSER engineering) and new 3.70 gears along with new 31 spline MOSER axles. Its held in place by a slightly modified NO LIMIT ENGINEERING 4 link FATBAR setup that gives much more stabilty and adjustabilty compared to stock. To duplicate this frame by yourself parts and materials alone would cost 7k or more. For any questions or more pics email, call, or text 2606023901.

Trim none

Chevrolet : C-10 none 1968 chevy 1 2 ton 4 x 4

$5,000

Oakland, Maryland

Year 1968

Make Chevrolet

Model C-10

Category -

Mileage 10000+

Posted Over 1 Month

1968 pick up truck, no side marker lightsruns, starts good, 4 wheel drive works well4 speed, works well, no leaksDoes have manual steering, Overall decent truck, typical of what you would find for ageneeds new bed flooringAny questions, call Travis at 301-533-6014 can text alsoSeller is in hospital for extended period of time so may not respond immediately.

Trim none

Chevrolet : C-10 C-10 1969 chevy c 10 swb fleet side

$17,000

Willow Springs, North Carolina

Year 1969

Make Chevrolet

Model C-10

Category -

Mileage 4000

Posted Over 1 Month

Pepper Metalic Gray exterior paint is less than two years old, 400 Small Block engine is pushing 450 horsepower with less than 4000 miles on the motor, 5 speed manual transmission

Trim None

Chevrolet : C-10 none 1971 blue chevy pickup 75 restored excellent condition has topper

$13,000

Windsor, Colorado

Year 1971

Make Chevrolet

Model C-10

Category -

Mileage 139900

Posted Over 1 Month

Nice 1971 Blue Chevy C-10. 75% restored with new paint and jammed. Has newly painted topper shell. New tires. Includes extra gauge cluster with stock tachometer.

Trim none

Chevrolet : C-10 none 1972 chevrolet c 10 long bed pickup truck

$3,200

Huachuca City, Arizona

Year 1972

Make Chevrolet

Model C-10

Category -

Mileage 124484

Posted Over 1 Month

1972 Chevy PU long bed for sale very low mileage for this year of vehicle I am the 3rd owner, (I bought it in 2001) this a basic truck with a 350 engine w/ electronic ignition, hooker headers, 650 Edelbrock carb and manifold, fairly new breaks, 3 speed on the floor, some rust nothing major.

Trim none

Chevrolet : C-10 c10 pick up 1972 chevrolet c 10

$6,995

Ardmore, Alabama

Year 1972

Make Chevrolet

Model C-10

Category -

Mileage 22000

Posted Over 1 Month

sales with alabama bill of sale but i do have the tennessee tittle for this truck...we dont title truck trucks in alabama but you may need it in your state you are buying a 1972 c10 swb pick up , great running project truck that was restored 10 years and now its that time again...odometer on truck reads 30,813 but unknown mileage on body...very dependable with 350 motor and 350 turbo transmission out of a 1993 Chevrolet truck with 22,000 miles on each....the seat is out of the same 1993 truck......brakes hard as a rock, blinkers, lights,wipers all work correctly.....the doors both operate excellent from the outside but needs attention from inside as does the windows they will roll up and down but need attention as well.... all the tires all have decent tread and will run for awhile......this truck is very dependable and mechanics are done in my book.....the body is straight down both sides as you can see in pictures and videos, ....this truck has one place on drivers side bed , one on drivers side door,one on passenger side front fender edge that needs body work....rockers seem fine.......clear coat is peeling on hood and on top of truck......truck needs restored but mechanics are done !.........inside the floor has patches in it and the inside of door were cut for speakers back in the day.............please watch videos and you decide for yourself.....copy and paste each link to watch 4 videos of truck inside, running motor and outside walk around, and driving away https://youtu.be/LffHuq4sYnQ https://youtu.be/ZI8fa7LhQc4 https://youtu.be/8jahFF2Rfn4 https://youtu.be/7NLQY6Ua6GM

Trim none

Chevrolet : C-10 none 1978 chevy stepside pick up

$5,200

Roseville, California

Year 1978

Make Chevrolet

Model C-10

Category -

Mileage 100000

Posted Over 1 Month

1978 chevy stepside pick up truck.This is a california rust free truck that is in pretty darn good shape for its age.Truck has been repainted recently(not by me)everything on the outside is in good shape.The truck runs good but needs a new battery and the radiator needs to be flushed and said hoses must be replaced.The interior is ok,its all there however the drivers side window doesnt work as the channels inside door need replacment.brand new tires on truck,truck is on non op ive been told.selling truck as is and hate to do so.this is a truck you dont see on the road anymore,so my dreams for it have been put away lol.Anyhow thanks for looking I can forward many more pics to your phone if needed im having issues uploading once again thank you

Trim none

Chevrolet : C-10 LT-4 1986 chevy c 10 custom classic pickup truck lt 4

$15,000

Miami, Florida

Year 1986

Make Chevrolet

Model C-10

Category -

Mileage 500

Posted Over 1 Month

Chevy c10 orig 50,000 mile truck all new high performance engine still at breakin evey nut and bolt is new internal and outer , 40 over corvette lt4 engine carburated , aluminum heads big springs 1.6 rockers, all arp bolts , all victor reinz performance gaskets,edelbrock , MSD ,high volume oil pump , just way to much to list...it's all new and no money spared ...long tube headers , h pipe, and killer spintech mufflers , side exhaust...Body is straight and no rust pretty much the best c10 there is no bondo no nothing , chassis was cleaned then spray lined lowered 4 front 6 rear with belltech , new suspension parts and performance swaybar...New tires and rims 5x5 ,,,for faster response on questions Call or text for any questions 786-333-2288

Trim None

Chevrolet : C-10 none 1971 chevrolet c 10

$1,295

Brady, Texas

Year 1971

Make Chevrolet

Model C-10

Category -

Mileage 100000

Posted Over 1 Month

1971 Chevy C-10 Pick up, has a good running straight 6cylinder 292Cu engine, was converted from a column shift to floor 4spd manual transmission. This truck is great for the person looking for that rebuilding project. Needs some light body work and comes with a extra front clip, the cab has some minor rust on the body part of the cab below the doors, also seat needs recovered along with some interior cosmetics. All the lights work and has a clear title. This is one of the last of the era of practical operational trucks with that strong 292 engine and has no computer diagnostics to check. The current front clip has a dent in the front left fender and has rust on the bottom part of the cab area below the doors. The seat needs recovered and or repaired, new door handles on the driver side door. Several small dents and dings on the entire vehicle , Paint is dull and needs new paint on the entire body of the truck. The bed is sound and do not see any evidence of rusted out areas.

Trim none

Chevrolet : C-10 NONE 1961 chevy apache 10 short bed fleet side

$3,000

Corona, California

Year 1961

Make Chevrolet

Model C-10

Category -

Mileage 999999

Posted Over 1 Month

1961 SHORT BED FLEET SIDE. NO MOTOR NO TRANS. HAS A LITTLE ROT AND FEW DENTS. OVER ALL GO START TO A GOOD PROJECT. LOOK AT PICS. YES I WILL SHIP. TITLE IN HAND. THANKS FOR LOOKING OLDDIRTYDANSAs far as the rot a little bit in the rocker.A little bit in above the windshield in corner .And the drip rail on the back. The roof has no rot. Look at the pics. SOLD AS IS. This roller is a nice start for one bad ass. TRUCK.........

Trim NONE

Chevrolet : C-10 none 1967 chevy short box stepside

$7,500

Gilman, Vermont

Year 1967

Make Chevrolet

Model C-10

Category -

Mileage 100000

Posted Over 1 Month

this is a very solid truck its not a rot box came from west va it needs some finishing. i replaced the inner fenders and radiator support they had some rust and i could have fixed them but chose to buy new ones the floors and rockers are solid and it doesent have a bunch of filler in it it runs and yard drives and the brakes are right there on it , it needs door locks, wipers, and the lights need to be hooked up and maybe some minor things were i live there are none of these trucks , so finding them is impossible in this condition , it has a small block and 350 auto trans, i have changed the wheels to a chevy rally wheel since i took these pics if you like these we can talk, what im asking for it is what i have in it, and i have other projects to finish so i have to let this one go i do have a restoration shop ,so if your interested in having me finish the truck i can do that if you dont have the experience or place to do it, any questions ill be glad to answer them thanks for looking

Trim none

Chevrolet : C-10 10 THIS IS A NON-RUNNING PROJECT

$3,500

North Highlands, California

Year 1967

Make Chevrolet

Model C-10

Category -

Mileage 25098

Posted Over 1 Month

THIS IS A NON-RUNNING PROJECT. IT DOES NOT RUN! BUT IT LOOKS LIKE A GOOD PROJECT. THE BODY IS IN PRETTY GOOD SHAPE (for the shape it's in). I THINK THE BED COULD BE SAND BLASTED AND PAINTED AND IT WOULD COME OUT GOOD. THE FLOOR PANS LOOK BETTER THAN THE DOOR JAMS. I DO NOT KNOW IF THE ENGINE TURNS OVER OR NOT BUT YOU WOULD - MORE THAN LIKELY - REBUILT OR REPLACE IT. AND I DON'T KNOW ABOUT THE TRANSMISSION. I WOULD PUT "ROLLER TIRES" ($40.) IF YOU NEED IT SHIPPED. IT IS BEING SOLD WITH NO RESERVE. WHO EVER HAS THE HIGHISH BID WILL BUY IT. THE "BUY IT NOW" IS FOR THE GUY THAT CAN'T WAIT FOR THE AUCTION TO FINISH. OTHER QUESTIONS : BEN 916-730-8830 - 8:00a.m. - 8:00 p.m. PST.

Trim NONE

Chevrolet : C-10 None 1972 chevy truck

$29,950

Olympia, Washington

Year 1972

Make Chevrolet

Model C-10

Category -

Mileage 15

Posted Over 1 Month

1972 Chevy Pick Up 1967 New core support and sheet metal nose with cowell Hood Windshield chopped 3 inches with blazer header, door cut to match body lines 12 point roll cage Tilt steering column Auto meter Phantom Comp gauges Budnick Wheels 20 X 9 in front 225/35 ZR 22 X11 in rear 305/40 R New tires Toyo Proxes S/T New Willwood Disc brakes with14 inch drilled rotors and Polished 6 piston calipers New 12 bolt rear end narrowed to fit under wheel wells, new 33 spline Dutchman axles New Detroit 12 bolt ratchet posi locker NewVintage Air New Air bags, compressors and tanks New remanufactured lower control arms for adjustable ride height Transmission tubo 400 New Painless wiring harness New 565 Big Block Motor New Custom sheet metal manifold with matched Dual 1050 Dominators carbs Motor is fully internally balanced World Merlin steel crank 14 to 1 compression JE pistons with total seal Hell Fire rings Eagle rods with CB743H rod bearings Billet Comp cam timing chain and gears Comp Roller cam 820 lift 290 duration with dura bond cam bearings Bill Jenking signiture Series Merling Heads Coated Super Comp equal length headers with cones Engine assembly and Flow work all done by Art Davidson Racing Motors, Puyallup WA Dynoed 870 Horsepower @ 6800 RPM 712 Torque @ 5262 RPM Barry Grant fuel pump 400 GPM New 10 AN steel braided line with new aluminum rear mounted tank Fuel VP 110 $18,500. in motor parts alone not to include assembly and dyno costs $12,500 in wheels, tires, and brakes $ 2,500 in rear end $ 2,000 in new front end sheet metal

Trim None

Chevrolet : C-10 NONE 1965 chevy c 10 longbed

$2,000

Corona, California

Year 1965

Make Chevrolet

Model C-10

Category -

Mileage 64780

Posted Over 1 Month

1965 CHEVY C10 LONGBED, SOLD AS IS. LOOK AT PICS. YES I WILL SHIP BUT YOU WILL HAVE TO PAY FOR SHIPPING AND HANDLING!! THE BODY IN GOOD SHAPE ! INSIDE THE CAB AS WELL! THE MOTOR IS IN THE BED PULLED APART. ALL OF THE REST OF THE PARTS TO PUT THIS TRUCK BACK ON THE ROAD ARE IN THE BED, GRILL BUMPER AND SO ON!!!!! HAVE CERTIFIED NOTARTY FOR APPLICATION FOR DUPLICATE OR PAPERLESS TITLE...SOLD AS IS..... THANKS FOR LOOKING OLDDIRTYDANS

Trim NONE

Chevrolet : C-10 none 66 chevy with 12 v cummins engine

$9,000

Skyland, North Carolina

Year 1966

Make Chevrolet

Model C-10

Category -

Mileage 999999

Posted Over 1 Month

1966 C10 Rat rod Truck. On the road for several years. Used as shop truck for shows and parts runner. Runs well with no major mechanical issues. It is a rat so there is rust. Holes in the floor patched with plates. The frame and truck as a whole are solid. Manual drum brakes and manual steering. Its a rough rider, it was not built to go across country. We have enjoyed it around the shop and at many local shows, it gets plenty of attention. We are moving on to the next project truck. No major work has been done to the motor, the pump is turned up a little. Please ask any questions we want someone who will appreciate the truck to get it. Thank you

Trim none