Chevrolet C 10 cars for sale in Watertown, South Dakota

Chevrolet : C-10 Custom 10 1972 chevy c 10 air suspension forgestar wheels 350 ci

$15,000

Watertown, South Dakota

82,500 miles (original)8'bedDrivetrain:original 350ci-good/even compression on all cylinders-aluminum intake-aluminum valve covers-aluminum radiator-HEI ignition-Sanderson coated headers-runs great/reliableTH350 trans (works perfectly)12 bolt w/Auburn 3.83 posiAir Ride:-Air Lift Dominator airbags- 8" of travel, 1/2" ports, 600 psi burst rate (four included)-AccuAir VU4 4-way Valve Manifold- Compact design, easy installation, four corner independent control-Viair 480 Chrome Compressor Dual Pack- includes two 200 psi chrome air compressors, relays, pressure switch, and more-5 gallon ALUMINUM air tank- perfect size for your ride, aluminum won't corrode or rust. Mounting feet on bottom for easy installation in your trunk.-3/8" DOT approved air line-Brass DOT approved PUSH-CONNECT air fittings- no leaks or failures with these quality parts!-AccuAir eLevel Ride Height Control System- height sensors at each wheel let you program 3 pre-set ride heights; handheld digital controller allows you to adjust your height at the touch of a button!-Front airbag bracket set- designed to fit your factory spring pockets and lower control arms.-Rear airbag bracket set- designed to fit your factory spring pockets and axle.-Bolt-on Frame Notch Kit- this notch, combined with a pair of lowering blocks, will give the rear of your truck an additional 2" of drop with no other modifications.The Accuair Management uses ride height sensors to maintain pre-set heights, regardless of load. It's a reliable system that's very easy to use. Auto calibrated and simple to adjust. The rest of the set-up is also top quality. The pumps, tank, lines, wires, and computer are all safely hidden from view with easy access. I can raise this up to stock height with a push of a button and it would appear stock...you don't have to ride low. The entire kit was ordered from BC Fabrication (BCFab.com) as their Level 4 kit. I was going to add the link, but eBay doesn't allow that.Wheels: Forgestar F14 20x10/20x8.5This is a custom built wheel, designed for this truck. It's hubcentric and lightweight.Suspension:CPP Front & Rear SwayCPP 2.5" drop spindlesCPP 2" drop blocks (rear)CPP rear shock angle brackets (new shocks)Stoptech drilled/slotted rotors & padsThe truck drives, shifts, rides, stops and handles really well. No vibrations, pulls, or other awkwardness.Body:This was a straight body to begin with, just had some rust (cab corners, rockers). I welded in new sheetmetal and filled (welded) all trim holes. It was painted with Hot Rod Flatz single stage urethane. It's a very low-maintenance upkeep. No waxing or polishing!All work was done to this truck last fall. I purchased it from a close friend who owned it since the early '90's. He's a mechanic with his own shop, and maintained the truck very well. I wanted to maintain its usefulness as a truck, so I left the box intact and made a point to make it drive well, ride well and be reliable. I've daily drove this most of the summer, several distance trips included, without issue. Interior: The interior was stripped and sprayed to match the exterior. The seat and carpet were in ok shape, so they were re-used. The seat has a crack in the vinyl (shown) where it flexes, but has no other tears or rips. New door panels and dash were installed. It doesn't have a radio, because I didn't like any of my options well enough to put one in. I haven't missed it, so it's stayed that way. I made a vinyl panel to cover the opening. The interior (floor/doors) are layered in Dynamat/Fatmat insulation. All the gauges work properly. Issues:The engine does leak some oil from the rear main seal. It also burns a small amount on warm start-up from the valve seals. The high-idle on the Quadrajet stopped working when I put the intake on, and it developed a stumble on WOT. Otherwise, everything works as it should. It is an older truck, though, and not every part is restored. There are signs of age in misc trim...dings/scuffs/etc. This makes a great driver that gets a lot of compliments, but I don't see it as a show truck. No Trades.

Trim Custom 10