Cars for sale in Patton, Pennsylvania

1995 Ford L9000 95 FORD L9000 Dump Truck New Steel Dump Bed 12' Plow Hoist St Steel Spreader Box

$19,900

Patton, Pennsylvania

This truck is in excellent running condition. Equipt w 12' plow, New Steel Dump Bed & hoist, New Stainless Spreader Box & Hydraulics. New Tires. New Front & Rear Disc Brakes and Clutch. Air & Cruise. 35000 GVW. 350 Cummins Motor. Had all gone over to clean haul roads, then mines shut down. Truck is ready to work for you. Asking $19,900. OBO Pics available.

Honda : Civic DX 1998 honda civic hatchback ej 6 ek 9 apexi hb

$2,000

Patton, Pennsylvania

Car is pretty solid for the year. Body is straight with very minimal "Honda" rust starting. It's been in the family and a reliable daily driver for the past ten years. Miles will go up slightly since it is still being driven almost daily. PA inspected until March. There are a few aftermarket parts and others have been replaced recently. I'll list everything below. The is a turn-key car so no work is needed to pick up and go or swap in a bigger engine like most people do with these. I'm listing this for my brother but I used to own the car as well and still love it. Pros -Megan racing header -Magnaflow catalytic converter -Apexi Noir Complete cat back exhaust -All suspension was replaced in 2010 with stock parts -Front and rear lip kit -Brand new fuel lines and clutch recently installed -All brakes are good -Radiator, spark plugs, timing belt and tensioner installed in last 20k miles -Alloy Honda 15" rims from a 2003 Civic Si w/ decent matching Kumho tires, 50% tread -Black housing headlights and tail lights Cons -Drivers side door handle is broken (including parts needed to fix) -Occasional issues with the wiper selector (including parts to fix) -Rear wiper needs replaced -Cabin hood release handle is broken but it can still be used to pop the hood (can include parts needed to fix if wanted) -Valve cover leaks a little (typical) -AC belt is not installed but I think it works (haven't cared to use it in the past few years) Thanks for looking and please ask any questions. Even though I'm not selling this for myself I should be able to answer anything quickly or get the answers if I don't have them. Test drives or inspections can be setup if needed.

Trim DX Hatchback 3 Door

1997 Mack RD690S

$24,000

Patton, Pennsylvania

1997 Mack RD690S Dump Truck, Mack tri axle 350+hp 7speed 18000front 46000rears 16ft steel dump READY TO BE PUT TO WORK ! Less than 100,000miles on rebuild. Less than 1,000 miles on injection pump. Cold A/C. Cruise control, Paint job is 2years old. Drives straight and true. $24000.00, 8149374042

Mercedes-Benz : 500-Series Leather 1983 Mercedes 500 sec Euro Spec model

$5,500

Patton, Pennsylvania

Clean Arizona car, same family owned since new. Dealer maintained until 2 years ago, has had less than 5000 miles put on it in last 4 years. Starts, runs, stops and drives well. 18in amg rims and new goodyear eagles. Car is good looking but does show normal wear and tear for a 31 year old classic. I rebuilt the driveshaft a month ago, front calipers were rebuilt last May. Interior and trunk are very clean, dash does have cracking but I will give new owner a perfect dash for the car, and a few replacement chrome pieces. The undercarriage is really clean. Exhaust is in great shape. Engine is very strong, car pulls hard. Transmission shifts perfect. A/C button on dash wont operate, and I would guess it would need a recharge. This is an early euro model, most research I ever did says this car wasn't supposed to have been built with a V-8 until 1984 but it was built in 1983. It was $58,500.00 new in 1983. I am moving in October and the car must go. Ask questions, or call 814-312-6076 ask for Chris. Current Pa. inspection. I drive it to work once a week. Thanks for looking.

Ford : Mustang Fox 1986 Ford Mustang Notch

$3,200

Patton, Pennsylvania

Up for auction is my 1986 Mustang notch. I am moving and I have to give up this project that I have owned for 6 years. Body is decent and had very lite rust on 1 rear fender well before being stripped and primed for paint. Underneath has been cleaned up and painted black. Engine bay also painted black. Body is primed and sealed with black primer sealer. 10 pt. cage, frame connectors, AJE tube K-member, coil over front suspension with camber/castor plates and tube a-arms. Rear sits on tube control arms and is a 3:73 posi. New fuel cell. Engine is a fresh 350sbc, early steel heads with big valves. Dynatech long tube headers($500.00). Lunati cam and good hydro lifters. Transmission is a Turbo 350, lots of good parts in tranny, clutches, steels and heavy duty sprag and center support. 3000 stall converter. Full manual valve body. Driveshaft is a stronger unit with all new components. Centerlines and B.F Goodrich tires all around. Interior is gutted except for a racing style seat. Some tin work. The mustang needs rear brake lines, fuel and coolant hoses. engine oil, transmission fluid and brakes fluid. Engine needs wired, New ignition panel and battery cut off will make wiring engine simple, I never planned on a street legal car as far as lighting goes, but original wiring is all there if someone wanted to make a road car out of it. Needs finished up. Will need an alignment. Car is for sale locally. Auction will end if sold locally. Email questions. Will sell as roller, make best offer or contact.